Tiltaing Sony a7siii Kit E - Tactical Gray

In a robust four-sided design fashioned in tactical gray, the Tilta Full Camera Cage for Sony a7S III provides two shoe mounts, a 15mm rod port, and an ARRI-standard rosette with an M6 thread for attaching optional handgrips. The rod port, which is built into the cage, is secured tightly with an integrated screw on the rear side of the port, using an included Allen key. The cage also offers 1/4"-20 and 3/8"-16 mounting threads for accessories, and there are multiple 1/4"-20 threads on the bottom of the cage that allow you to find the optimal balance for your camera when mounting on tripods, gimbals, and other supports.

Carry and stabilize your Blackmagic Design Pocket Cinema Camera 4K with this lightweight tactical gray Quick Release Top Handle from Tilta. The quick release handle's features include two shoe mounts, a 15mm rod port, multiple 1/4"-20 and 3/8"-16 threads, and a 3/8"-16 thread with locating pins.

The aluminum and stainless steel handle attaches to your camera cage using the included spring-loaded thumbscrew. The 15mm rod port features a rod locking screw to add a rod to the handle. There is one 3/8"-16 thread with locating pins on the front of the handle to mount a separately available Tilta cage rod mount.

The HDMI Cable Clamp Attachment for Sony a7S III Full Cage from Tilta attaches to the side of the cage with a single screw and a locking pin to clamp your HDMI cable connector and prevent it from accidental disconnection. This version of the clamp is designed in tactical gray to best match the tactical gray version cage. After securing the clamp to the cage, you can use the included Allen key to tighten it around the cable connector by tightening the integrated screw at the top of the clamp. The integrated screw is ridged, so you can tighten it with your fingers as well, although not as tight.

Using two included screws, the compact Manfrotto Quick Release Plate, in Tilta gray, attaches to the bottom of Tilta full and half camera cages for the Sony a7S III. The cage can then be mounted directly on tripod heads, ball heads, and other supports that accept Manfrotto camera plates.

Using two included screws, the compact Arca-Swiss Quick Release Plate, in Tilta gray, attaches to the bottom of Tilta full and half camera cages for the Sony a7S III. The cage can then be mounted directly on tripod heads, ball heads, and other supports that accept Arca-Swiss camera plates.

The Advanced Left-Side Handle Adapter Type VI from Tilta enables you to mount a Tiltaing Left-Side Wooden Handle to the NATO rail mount on select Tilting camera cages. This Tilta gray Type VI adapter is constructed of aluminum and stainless steel and comes with an Allen key.

This Tilta gray Tiltaing 15mm LWS Baseplate Type II from Tilta features two mounting surfaces. The top of the baseplate allows for mounting of Tiltaing half and full camera cages for Panasonic GH5 series, Fuji XT3/4, Nikon Z6/Z7, and Sony a6/a7/a9 cameras. The bottom of the baseplate mounts on Tilta standard dovetails. The bottom also incorporates three 1/4"-20 threaded holes for mounting the baseplate directly on a tripod. Built into the baseplate is a pair of LWS 15mm rod clamps with spring-loaded locking levers.

This Tilta Single 15mm Aluminum Rod is 7.87" in length and anodized black. It is compatible with 15mm LWS and studio rod support clamps and chamfered to make it easier to slide rod-mounted accessories onto the end.

This HDMI Extension Cable from Tilta is primarily designed to connect to your camera inside your Tiltaing cage, providing you with an ergonomic method of wiring your camera to an external HDMI monitor. Simply plug the male HDMI end into the camera, and connect your display's HDMI cable to the female port of this extension cable. It is also compatible with Tilta's HDMI cable clamps for security.

The Tiltaing Run/Stop Cable from Tilta connects the Tiltaing Advanced Side Handle to your Sony a6, a7, or a9 series camera, enabling run/stop triggering with the push of a button.